Introduction: LED Growing

This plan is almost exploitation Light-emitting diode to helps plants uprise.

Ruby-red LED can help plant's Promote sidelong branching and tillering

Green LED give the sack help plants Strengthen growth

Depressed LED can help plant life Abridge internodes, reduce leaf surface area, reduce relative growth rate, and increase nitrogen ratio

And this project gather 3 LED to have the plants growing work getting easier.

Which part of the plant that you are not satisfaction, you can use up the other LED to change information technology.

Abuse 1: Things to Use

Prepare cardboard x 6

Red Led x 3, Green LED x 3, Gentle LED x 3

Cellophane x 1

Breadboard x 1

wire x 21

Resistance x 9

Botton x 3

Step 2: How It Works?

Three Button

when to labour, one of them, the Carmine LED will shine

one of them, the Green LED will shine

one of them, the Blue LED will shine

Step 3: Code

void frame-up(){ // put your setup code Here, to running play once:

pinMode( 4 , INPUT); // sets the digital pin A input pinMode( 11 , Yield); // sets the digital pin as output pinMode( 12 , OUTPUT); // sets the extremity pin as outturn pinMode( 13 , OUTPUT); // sets the digital pin as production pinMode( 3 , Stimulus); // sets the integer pin equally input pinMode( 8 , OUTPUT); // sets the digital immobilise as output pinMode( 9 , OUTPUT); // sets the appendage pin equally output pinMode( 10 , OUTPUT); // sets the digital bowling pin as output pinMode( 2 , INPUT); // sets the digital pin as input pinMode( 5 , OUTPUT); // sets the digital pin As output pinMode( 6 , End product); // sets the whole number pin arsenic output pinMode( 7 , OUTPUT); // sets the digital pin Eastern Samoa production }

emptiness loop(){ // put your primary code here, to run repeatedly: if (digitalRead( 4 )) { digitalWrite( 11 , HIGH ); // sets the whole number pin happening/off digitalWrite( 12 , Alto ); // sets the integer pin on/off digitalWrite( 13 , Shrill ); // sets the digital PIN number connected/off delay( 5000 ); // waits a some milliseconds digitalWrite( 12 , Broken ); // sets the digital pin happening/off digitalWrite( 13 , LOW ); // sets the digital pin on/murder digitalWrite( 11 , LOW ); // sets the member pin on/off } if (digitalRead( 3 )) { digitalWrite( 8 , In high spirits ); // sets the digital pin along/off digitalWrite( 9 , HIGH ); // sets the digital pin on/forth digitalWrite( 10 , HIGH ); // sets the digital pin on/murder delay( 5000 ); // waits a few milliseconds digitalWrite( 8 , LOW ); // sets the whole number pin on/off digitalWrite( 9 , Downhearted ); // sets the digital PIN along/off digitalWrite( 10 , LOW ); // sets the digital pin on/off } if (digitalRead( 2 )) { digitalWrite( 5 , HIGH ); // sets the digital pin connected/forth digitalWrite( 6 , HIGH ); // sets the digital pin on/off digitalWrite( 7 , HIGH ); // sets the digital pin on/off delay( 5000 ); // waits a few milliseconds digitalWrite( 5 , LOW ); // sets the digital pin on/off digitalWrite( 6 , Down in the mouth ); // sets the digital pin on/off digitalWrite( 7 , LOW ); // sets the digital pin on/off } }

(You needs to change the delay(5000) to how long you necessarily, or wants the LED radiancy )

Abuse 4: How to Make the Look?

Cut the cardboard into 3 different types

Fell three golf hole on the two slope of the composition board, to let the button pass over

abbreviate a trifle hole that can let the Cable through

use of goods and services Hot melt gun to stick them every.

If you neediness, you can stick the Cellophane on the cardboard, that tail end let you see the inside.

Step 5: Finish All

Stick the Arduino on the top of the cardboard

fixed the button on the buttonhole

At last check if it industrial plant!

Be the First to Share

Recommendations

  • Anything Goes Contest 2021

    Anything Goes Contest 2021